QUESTIONS?
904-731-0103
Maximize your savings
Located in Jacksonville, Florida
Blades from high quality steel
Part# B1EM1810 Each Price (6 or More): $14.9017-29/32" XHT Wavy Mulching Blade for older 36" and 52" Exmark mower models. But it can also replace several other brands of mowers with the same deck sizes, such as: Ariens/Gravely, Bobcat, older Exmark, Ferris, Husqvarna, Snapper, older Toro and more. XHT (Xtreme Hardness & Toughness) blades are 25-40% harder than standard lawnmower blades. Benefits of the XHT blade are sharper and longer lasting cutting edges. More resistance to bending. XHT blades also offer greater impact toughness.
Part# 96-318 Each Price (6 or More): $17.9517-7/8" Oregon Gator G3 Mulching Blade used on 36"/52" Raptor Series, Sport, Super S, Super Z and X-ONE models. Also used on 36"/52" BigDog Alpha, Alpha MP, Diablo, Hike, Trooper and X Series models. The G3 Gator blade is the best option for those looking for a replacement blade with better mulching capabilities.
Part# 396-704 Each Price (6 or More): $18.8517-7/8" Oregon Gator G6 HD Mulching Blade used on 36" and 52" Hustler and Big Dog models. Tungsten carbide is fused into the blade, creating an ultra-hard layer at the cutting edge and increasing the time between sharpening. Cleaner, more efficient cutting performance can eliminate the need to bag, saving time, and reducing hassles. Up to twice the cutting length for increased cutting efficiency with each revolution. Greater width and thickness extends blade life and allows for longer lifting arch to improve bagging and mulching.
Part# 92-044 Each Price (6 or More): $12.2517-7/8" Oregon High Lift Blade used on 36"/52" Raptor Series, Sport, Super S, Super Z and X-ONE models. Also used on 36"/52" BigDog Alpha, Alpha MP, Diablo, Hike, Trooper and X Series models. X-Tended Cutting Length optimizes the cutting efficiency with each revolution. The aggressive blade angle increases air flow to push debris up-and-out for superior bagging or side discharge.
Part# B1PD5008 Each Price (6 or More): $15.2518" Predator Series HD Mulching Blade used on 36" & 52" models. Such as Bad Boy, Bobcat, early Exmark, Ferris, Gravely, Husqvarna, John Deere, Toro and more. Predator blades provide the flat blade design preferred by most commercial mowers with an extended cutting length for increased cutting efficiency.
Part# 93-601 Each Price (6 or More): $18.9518" Oregon Gator G3 Mulching Blade used on 36"/52" Bobcat XM Series mowers. Also used on 52" Wright Mfg Stander X and Sport X models. The Gator G3 blades offer superior mulching, fewer bag stops, and cleaner side discharge than the standard manufacturer blade.
Part# 96-344 Each Price (6 or More): $16.9518" Oregon Gator G3 Mulching Blade used on various 36" and 52" models. Such as Bad Boy, Ferris, Great Dane, John Deere, Scag, Toro and more. Up to twice the cutting length for increased cutting efficiency. The aggressive blade angle increases air flow to push debris up-and-out for superior bagging or side discharge.
Part# 96-322Each Price (6 or More): $13.7518" Oregon Gator G3 Mulching Blade used on 36" & 52" Exmark Metro, Pioneer, Turf Tracer, Lazer Z, Radius and more. Also used on Newer Toro ZMaster models, using 15/16" center hole and require a splined blade bushing. Up to twice the cutting length for increased cutting efficiency with each revolution. The aggressive blade angle increases air flow to push debris up-and-out for superior bagging or side discharge. Cleaner, more efficient cutting performance can eliminate the need to bag, saving time, and reducing hassles.
Part# 396-726 Each Price (6 or more): $22.2518" Oregon Gator G6 Heavy Duty Mulching Blade used on several 36" and 52" models. Such as Bad Boy, older Exmark, Ferris, Jacobsen, John Deere, Snapper, Scag, Toro and more. Tungsten carbide is fused into the blade, creating an ultra-hard layer at the cutting edge and increasing the time between sharpening. Cleaner, more efficient cutting performance can eliminate the need to bag, saving time, and reducing hassles. Up to twice the cutting length for increased cutting efficiency.
Part# 396-322Each Price (6 or More): $18.4518" Oregon Gator G6 Heavy Duty Mulching Blade used on 36" & 52" Exmark Metro, Pioneer, Turf Tracer, Lazer Z, Radius and more. Also used on New style Toro ZMaster models that use 15/16" center hole and require a splined blade bushing. Tungsten carbide is fused into the blade, creating an ultra-hard layer at the cutting edge and increasing the time between sharpening. Cleaner, more efficient cutting performance can eliminate the need to bag, saving time, and reducing hassles. Up to twice the cutting length for increased cutting efficiency with each revolution. Greater width and thickness extends blade life and allows for longer lifting arch to improve bagging and mulching.
Part# B1EM1883 Each Price (6 or More): $12.9518" XHT High Lift Blade used on 36" & 52" Exmark and newer Toro models. Blade center holes require a splined blade bushing. XHT (Xtreme Hardness & Toughness) blades are 25-40% harder than standard lawnmower blades. Benefits of the XHT blade are sharper and longer lasting cutting edges, and more resistance to bending. XHT blades also offer greater impact toughness.
Part# 91-623 Each Price (6 or more): $13.2518" Oregon Extended High Lift Blade used on 36"/52" Scag & Ferris models. Also used on various 36"/52" models, such as Bad Boy, Gravely, Husqvarna, Toro, Wright Mfg and more. Oregon blades are individually straightened and hardened to provide a consistent, cleaner cut and increase blade longevity. X-Tended Cutting Length optimizes the cutting efficiency with each revolution
Part# 792-030 Each Price (6 or More): $11.5018" Oregon High Lift Blade used on 36" & 52" Exmark Metro, Pioneer, Turf Tracer, Lazer Z, Radius and more. Also used on New style Toro ZMaster models that use 15/16" center hole and require a splined blade bushing. Oregon blades are individually straightened and hardened to provide a consistent, cleaner cut and increase blade longevity. X-Tended Cutting Length optimizes the cutting efficiency with each revolution.
Part# 793-010 Each Price (6 or More): $12.2518" Oregon High Lift Blade used on 36"/52" Bobcat XM Series mowers. Also used on 52" Wright Stander X, and Sport X models. Oregon blades are individually straightened and hardened to provide a consistent, cleaner cut and increase blade longevity. The aggressive blade angle increases air flow to push debris up-and-out for superior bagging or side discharge.
Part# 26-003Each Price (6 to 29): $12.21Each Price (30 or more): $11.7118" EMP High Lift Heavy Duty Blade used on 36" & 52" models. Such as Bad Boy, Bobcat, Ferris, Gravely, Husqvarna, Scag, Wright Mfg and more. With EMP brand of blades you’ll find our blades made with 100% Hi-carbon alloy steel specifically engineered for mower blade applications. EMP brand of blades are made with full austemper heat-treating for maximum wear, hardness, and impact resistance. They are computer balanced to ensure minimum vibration and maximum spindle life. Every blade is individually computer straightened for a next to perfect cut. EMP High lift blades are ideal for cutting thinner blade grasses such as Bluegrass, Rye and Zoysia.
Part# 91-184 Each Price (6 to 29): $12.75 Each Price (30 or More): $12.2518" Oregon High Lift HD Blade used on 36" & 52" models. Such as Bad Boy, Bobcat, Ferris, Gravely, Husqvarna, Scag, Wright Mfg and more. The aggressive blade angle increases air flow to push debris up-and-out for superior bagging or side discharge. X-Tended Cutting Length optimizes the cutting efficiency with each revolution
Part# B1BC1202Each Price (6 or more): $12.50Each Price (30 or more): $12.0018" XHT High Lift HD Blade used on various 36" & 52" models. Such as: Bad Boy, Bobcat, Exmark, Ferris, Great Dane, Husqvarna, Snapper, Scag, John Deere, Toro, Wright Mfg and more. XHT (Xtreme Hardness & Toughness) blades are 25-40% harder than standard lawnmower blades. Benefits of the XHT blade are sharper and longer lasting cutting edges, and more resistance to bending. XHT blades also offer greater impact toughness.
Part# B1LE188318" Lazer Edge Self Sharpening High Lift Blades used on 36" & 52" Exmark and newer Toro models. Blade center holes require a splined blade bushing. Utilizing EverSharp™ technology these hardened steel blades deliver superior performance and actually get sharper during use, resulting in minimal maintenance and maximum profitability for landscaping professionals. In abrasive conditions, a blade can get dull in as little as four hours. After putting the blade to work for 50 hours, the results were clear. The LaserEdge® blade edge was still sharp, and the untreated side was dulled and worn away.
Part# 91-622 Each Price (6 to 29): $11.99Each Price (30 or More): $11.4918" Oregon Medium Lift Blade used on several brands of 36" and 52" mower models. Oregon blades are individually straightened and hardened to provide a consistent, cleaner cut and increase blade longevity. X-Tended Cutting Length™ optimizes the cutting efficiency with each revolution
Part# 26-018 Each Price (6 to 29): $12.21 Each Price (30 or More): $11.71
Part# 26-718 Each Price (6 or More): $12.45 Each Price (30+): $11.9518" EMP Medium Lift Heavy Duty Blade used on 36" & 52" Exmark Lazer Z, Pioneer, Radius, Turf Tracer models and more. Also used on new Toro models with a 15/16" center hole using a splined blade bolt bushing. With EMP's brand of blades you’ll find our blades made with 100% Hi-carbon alloy steel specifically engineered for mower blade applications. EMP brand of blades are made with full austemper heat-treating for maximum wear, hardness, and impact resistance. They are computer balanced to ensure minimum vibration and maximum spindle life. Every blade is individually computer straightened for a next to perfect cut. EMP Medium lift blades are ideal for cutting broad leaf grasses such as St. Augustine and Fescue. Most customers prefer our brand of blades over all the aftermarket brands.
Part# 91-235 Each Price (6 or More): $20.9518" Oregon Low Lift HD Blade is used on several brands of 36" and 52" mower models. Oregon blades are individually straightened and hardened to provide a consistent, cleaner cut and increase blade longevity. X-Tended Cutting Length™ optimizes the cutting efficiency with each revolution. Low Lift blades are best used in sparse, rough, sandy conditions to reduce wear on your deck and blades.
Part# 791-335 Each Price (6 or More): $14.9518" Oregon Wavy Mulching Blade used on 36" & 52" models. Such as Bad Boy, Bobcat, Ferris, Gravely, Husqvarna, Scag, Wright Mfg and more. The Oregon wavy mulching blade delivers a cleaner cut and quality results.
Part# 29-945 Each Price (6 to 29): $12.25Each Price (30 or More): $11.7518" EMP T4 Heavy Duty Mulching Blade used on several brands of 36" and 52" mower models. Such as: Bad Boy, Bobcat, older Exmark, Ferris, Gravely/Great Dane, Husqvarna, John Deere, Toro and more. EMP's brand of blades are made with full austemper heat-treating for maximum wear, hardness, and impact resistance. They are computer balanced to ensure minimum vibration and maximum spindle life. Every blade is individually computer straightened for a next to perfect cut. EMP T4 Mulching HD blades are the most popular design in commercial mowing. Our 4 Tooth design forces clippings back into the air flow for superior cutting without requiring a mulch kit. Extremely great for fall and spring clean ups, where leaves need shredding amongst other debris. Most customers prefer our brand of blades over all the aftermarket brands. Extended wear in sandy or extreme mowing conditions
Part# 29-718 Each Price (6 or More): $12.50 Each Price (30+): $12.0018" EMP T4 Mulching Heavy Duty Blade used on 36" & 52" Exmark models Pioneer, Turf Tracer, Lazer Z, Radius and more. Also used on New style Toro models that use the large center hole and require a spline blade bushing. EMP brand of blades are made with full austemper heat-treating for maximum wear, hardness, and impact resistance. They are computer balanced to ensure minimum vibration and maximum spindle life. Every blade is individually computer straightened for a next to perfect cut. EMP T4 Mulching HD blades are them most popular design in commercial mowing. Our 4 Tooth design forces clippings back into the air flow for superior cutting without requiring a mulch kit. Extremely great for fall and spring clean ups, where leaves need shredding amongst other debris. Most customers prefer our brand of blades over all the aftermarket brands.
Part# 29-045Each Price (6 to 29): $11.50 Each Price (30 or more): $11.0018" EMP T4 Mulching Blade used on various 36" & 52"models. Such as: Bad Boy, Bobcat, early Exmark, Ferris, Gravely/Great Dane, Husqvarna, John Deere, Toro and more. EMP's brand of blades are made with full austemper heat-treating for maximum wear, hardness, and impact resistance. They are computer balanced to ensure minimum vibration and maximum spindle life. Every blade is individually computer straightened for a next to perfect cut. EMP T4 Mulching blades are them most popular design in commercial mowing. Our 4 Tooth design forces clippings back into the air flow for superior cutting without requiring a mulch kit. Extremely great for fall and spring clean ups, where leaves need shredding amongst other debris. Most customers prefer our brand of blades over all the aftermarket brands.
Part# 28-187 Each Price (6 or More): $11.75 Each Price (30+): $11.2518" EMP Wavy Mulching Blade used on 36" & 52" Exmark Metro, Pioneer, Staris, Turf Tracer, Lazer Z, Radius and more. Also used on New style Toro ZMaster models that use 15/16" center hole and require a splined blade bushing. With EMP's brand of blades you’ll find our blades made with 100% Hi-carbon alloy steel specifically engineered for mower blade applications. EMP brand of blades are made with full austemper heat-treating for maximum wear, hardness, and impact resistance. They are computer balanced to ensure minimum vibration and maximum spindle life. Every blade is individually computer straightened for a next to perfect cut. EMP's original "Double-hump" Wavy Mulching blade design performs best when used with mulch kits and closed chute mowers. When used with factory installed mulch kits our blade provides one outstanding cut lawn.
Part# 28-618 Each Price (6 or More): $11.95 Each Price (30+): $11.4518" EMP Wavy Mulching Blade used on various 36" & 52" models. Such as Bad Boy, Bobcat, Exmark, Ferris, Gravely, John Deere, Scag, Toro, Wright Mfg and more. With EMP's brand of blades you’ll find our blades made with 100% Hi-carbon alloy steel specifically engineered for mower blade applications. EMP brand of blades are made with full austemper heat-treating for maximum wear, hardness, and impact resistance. They are computer balanced to ensure minimum vibration and maximum spindle life. Every blade is individually computer straightened for a next to perfect cut. EMP's original "Double-hump" Wavy Mulching blade design performs best when used with mulch kits and closed chute mowers. When used with factory installed mulch kits our blade provides one outstanding cut lawn. Most customers prefer our brand of blades over all the aftermarket brands.
Part# 92-027 Each Price (6 or More): $12.9518" Oregon Mulching Blade used on 36" & 52" Exmark Metro, Pioneer, Staris, Turf Tracer, Lazer Z, Radius and more. Also used on New style Toro ZMaster models that use 15/16" center hole and require a splined blade bushing. The Oregon wavy mulching blade delivers a cleaner cut and quality results. Oregon replacement lawn mower blades are made to the exact OEM specification for optimum performance.
